Modal Analysis of Micro-Electromechanical Systems

Tauseef Aized, Sania Azam, Ghulam Moeen Uddin, Muhammad Ali Azam

Abstract


Effects of ambient pressures on dynamics of two different micro cantilevers arrays were studied using ANSYS simulations. One array had substrate of N Type Silicon while other model was assigned Quartz as its substrate material, while the beams of both models had same material of polysilicon. Modal and Transient analyses were performed to obtain resonance frequencies and FRF curves of all beams. FRF curves were analyzed to obtain damping ratios and quality factors for each beam of both models. Comparison between resonance frequencies, Damping ratios and Quality factors of two arrays were to see the effects of substrate material over sensitivity of array. One of the geometric parameter (Gap height) was also studied under ambient pressures to check the dependency of energy dissipation mechanism over gap height of micro beams form their substrate.


Full Text:

PDF

References


Dehrouyeh-Semnani, A. M. and M. Nikkhah-Bahrami 2015). A discussion on evaluation of material length scale parameter based on micro-cantilever test. Composite Structures Vol:122: pp:425-429.

Ozdoganlar, O. B., B. D. Hansche, et al. (2005). Experimental modal analysis for microelectromechanical systems. Experimental Mechanics Vol:45(6): pp: 498-506.

Sumali, H. and T. G. Carne (2003). Air-Drag Damping on Micro-Cantilever Beams. Society for Experimental Mechanics. Bethel, America:pp: 788-794.

Khabir, M. G., S. Azizi, et al. (2017). Dynamics of a capacitive electret-based microcantilever for energy harvesting. arXiv preprint arXiv:1701.08843.

Blom, F., S. Bouwstra, et al. (1992). Dependence of the quality factor of micromachined silicon beam resonators on pressure and geometry. Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena Vol:10(1): pp:19-26.

Yasumura, K. Y., T. D. Stowe, et al. (2000). Quality factors in micron-and submicron-thick cantilevers. Journal of Microelectromechanical Systems Vol:9(1): pp: 117-125.

Cheng, Y.-C., M.-T. Lin, et al. (2010). Static and dynamic mechanical properties measurement of micro-nano metal thin film using cantilever beam deflection. Design Test Integration and Packaging of MEMS/MOEMS (DTIP), 2010 Symposium on, IEEE.

Kahrobaiyan, M., M. Asghari, et al. (2010). Investigation of the size-dependent dynamic characteristics of atomic force microscope microcantilevers based on the modified couple stress theory. International Journal of Engineering Science Vol:48(12): pp: 1985-1994.

Borkar, P., J. Kalambe, et al. (2013). Impact of design parameters on actuation voltage and response time for micro-cantilever based device. India Conference (INDICON), 2013 Annual IEEE, IEEE.

McFarland, A. W., M. A. Poggi, et al. (2005). Characterization of microcantilevers solely by frequency response acquisition. Journal of Micromechanics and Microengineering Vol:15(4):pp:785.

Hawari, H., Y. Wahab, et al. (2014). Design and analysis of various microcantilever shapes for MEMS based sensing. Journal of Physics: Conference Series, IOP Publishing.

Paul, S. and F. Clough (1999). Substrate sensitivity of the adhesion and material properties of RF-PECVD amorphous carbon. MRS Proceedings, Cambridge Univ Press.

Fu,Y. and J. Zhang (2010). Electromechanical dynamic buckling phenomenon in symmetric electric fields actuated microbeams considering material damping. Actamechanica Vol:215 (1): pp: 29-42.

Hosaka, H., K. Itao, et al. (1994). Evaluation of energy dissipation mechanisms in vibrational microactuators. Micro Electro Mechanical Systems, 1994, MEMS'94, Proceedings, IEEE Workshop on, IEEE.

Barhen,S. (2008). Analytic and numerical modeling of the transient dynamics of a microcantilever sensor. Physics Letters A Vol:372(7): pp: 947-957.

Afshari,M, S. Nima Mahmoodi. (2008). Nonlinear vibrations of piezoelectric microcantilevers for biologically-induced surface stress sensing, Communications in Nonlinear Science and Numerical Simulation,Vol: 13, Issue 9, pp:1964-1977, ISSN 1007-5704.






Copyright (c) 2019 Pakistan Journal of Engineering and Applied Sciences

Powered By KICS